How to Fix The Tension Springs On A Recliner

The tension springs on a recliner are designed to produce a rocking motion. They may become loose or broken over time. You can fix the tension springs on a recliner by following a few simple steps. In this article, we will show you how to fix the spring on a recliner step by step.

Where does the Spring go on a Recliner?

When you sit on a recliner, your weight pushes down on the chair. This in turn activates a mechanism that moves the backrest and leg rest away from the seat. This mechanism is known as a “reclining action,” and it is powered by springs. Over time, these springs can become worn out or damaged, and they may need to be replaced.

The first step in replacing the springs on a recliner is to remove the old ones. Depending on the type of recliner, there may be one spring or two springs located under the seat. These springs are usually held in place by clips or brackets. Once you have located the springs, you will need to use a screwdriver to remove the clips or brackets that are holding them in place.

With the old springs removed, you can now install the new ones. Begin by attaching one end of the spring to the frame of the recliner. Make sure that the spring is securely in place before moving on to the other end. Once both ends of the spring are attached, you can test the recliner to see if it is working properly. If not, make any necessary adjustments until it is functioning correctly.

Can you Adjust the Springs on a Recliner?

If your recliner has become too soft or saggy, you may be able to adjust the springs to restore their original firmness. This is a relatively simple process that can be done in just a few minutes.

First, locate the springs on your recliner. They are usually located near the base of the chair, underneath the upholstery. Once you have found the springs, use a screwdriver to loosen or tighten them as needed. If your recliner has multiple springs, make sure to adjust all of them evenly so that the chair remains balanced.

Once you have adjusted the springs, test out your recliner to see if it is now at the desired level of firmness. If not, simply repeat the process until you achieve the perfect level of support. With a little trial and error, you should be able to get your recliner feeling like new again in no time.

How do you Replace the Tension Spring on a Recliner?

If your recliner is starting to feel a little less comfortable than it used to, it may be time to replace the tension spring. This process is not as difficult as it may seem and can be done in just a few simple steps.

What You’ll Need are Tension springs, screwdrivers, and Pliers.

Remove the Old Tension Spring

The first step is to take out the screws that hold the seat and backrest on. You should be able to find these at the bottom of the chair. After removing them, use a screwdriver or a wrench if necessary. Once you have removed all of these screws, you need to gently lift up the backrest and pull it away from the springs. This will allow you to see all of them clearly and work on fixing them one at a time.

Install the New Tension Spring

Now it’s time to install the new tension spring. Start by threading one end of the spring through the hole in the recliner frame. Then, use your pliers to twist the other end of the spring until it’s securely in place.

Test It Out

Before you put your recliner back together, it’s a good idea to test out the new tension spring to make sure it’s working properly. Sit in the recliner and see if you can recline it without any issues. If everything seems to be working fine, then you’re all done!

How do you Loosen a Recliner Spring?

If your recliner has become difficult to open and close, it may be time to loosen the springs. This process is relatively simple and can be done in just a few minutes. All you need is a screwdriver and a few minutes of time.

First, locate the screws that hold the back of the recliner in place. There are usually two screws, one on each side. Use your screwdriver to loosen these screws until they are no longer tight.

Once the back screws have been loosened, you should be able to easily move the back of the recliner. Be careful not to force it, as this could damage the mechanism. Simply wiggle the back until it comes loose, then set it aside.

Related posts

Leave a Reply

Your email address will not be published.